The effect of band offsets of absorption layer on CNTS / ZnS / ZnO solar cell by SCAPS-1D
Article Sidebar
Main Article Content
Abstract
The ZnO/ZnS/ CNTS solar cell was studied using SCAPS-1D simulation. The cell efficiency was 9.38% and to improve the cell a back reflection layer (BSL) was added, so the conversion efficiency increased to 10.65% and we entered buffer layers, thus the cell structure became ZnO / Buffer / CNTS the conversion efficiency increased to 10.78%. It turns out that the effect of the buffer layer is greater than the reflection layer. The best cell was ZnO/CdS/CNTS/Cu2O and the conversion efficiency was 12.09%, fill factor 62.98%, short circuit current 20.01 mA/cm2 finally open circuit voltage 0.95V.
Downloads
Article Details
Issue
Section
This work is licensed under a Creative Commons Attribution 4.0 International License.
Tikrit Journal of Pure Science is licensed under the Creative Commons Attribution 4.0 International License, which allows users to copy, create extracts, abstracts, and new works from the article, alter and revise the article, and make commercial use of the article (including reuse and/or resale of the article by commercial entities), provided the user gives appropriate credit (with a link to the formal publication through the relevant DOI), provides a link to the license, indicates if changes were made, and the licensor is not represented as endorsing the use made of the work. The authors hold the copyright for their published work on the Tikrit J. Pure Sci. website, while Tikrit J. Pure Sci. is responsible for appreciate citation of their work, which is released under CC-BY-4.0, enabling the unrestricted use, distribution, and reproduction of an article in any medium, provided that the original work is properly cited.
How to Cite
References
[1] Skhouni, O.et al. (2017). Boosting the Performance of Solar Cells with Intermediate Band Absorbers the Case of ZnTe: O. Journal of Energy and Power Engineering, 11:417-426. [2] Simya, O.K.et al. (2014). Dye-sensitized solar cells based on visible-light-active TiO2 heterojunction nanoparticles. Synthetic metals, 188:124-129. [3] Sarkar, S.et al. (2018). Flower-like Cu2NiSnS4 microspheres for application as electrodes of asymmetric supercapacitors endowed with high energy density. CrystEngComm, 20(10):1443-1454. [4] Khattak, Y.H.et al. (2018). Effect of Cu2O hole transport layer and improved minority carrier life time on the efficiency enhancement of Cu2NiSnS4 based experimental solar cell. Journal of Renewable and Sustainable Energy, 10(4):043502. [5] Wang, T.X. et al. (2014). Flower-like Cu2NiSnS4 nanoparticles synthesized by a facile solvothermal method. Materials Letters, 124: 148-150. [6] Skhouni, O. et al. (2016). Numerical study of the influence of ZnTe thickness on CdS/ZnTe solar cell performance. The European Physical Journal Applied Physics, 74(2):24602. [7] Hameed, K.Y. et al. (2019). Modelling of novel-structured copper barium tin sulphide thin film solar cells. Bulletin of Materials Science, 42(5):.231. [8] Ganvir, R. (2016). Modelling of the nanowire CdS-CdTe device design for enhanced quantum efficiency in Window-absorber type solar cells. .University of Kentucky.
[9] Baig, F. (2019). Numerical analysis for efficiency enhancement of thin film solar cells. Ph.D. thesis, Instituto de Diseño para la Fabricación, Universitat Politècnica de València, Spain: 164pp
[10] Like .S. M. (1990) .The localization of both .Ghaleb, F. and Ahmed, H. A. Physics and Technology of Semiconductor Devices, Al-Hikma House for Printing and Publishing, Mosul. (In Arabic). [11] Khattak, Y.H. (2019). CZTSe Kesterite as an Alternative Hole Transport Layer for MASnI3 Perovskite Solar Cells. Journal of Electronic Materials, 48(9):.5723-5733. [12] Cherouana, A. and Labbani, R. (2017). Study of CZTS and CZTSSe solar cells for buffer layers selection. Applied Surface Science, 424:.251-255. [13] Minbashi, M.et al.(2017). Comparison of theoretical and experimental results for band-gap-graded CZTSSe solar cell. Current Applied Physics, 17(10): 1238-1243. [14] Omrani, M. K.et al. (2018). Improve the performance of CZTSSe solar cells by applying a SnS BSF layer. Solid-State Electronics, 141: 50-57. [15] Anuforonini, G. and Duduyemi, O. (2016). Simulation of the performance of CdTe/CdS/ZnO multi-junction thin film solar cell. Simulation, 3(1):1-10.
[16] Boumaour, M. et al. (2019). High efficiency silicon solar cells with back ZnTe layer hosting IPV effect: a numerical case study. Journal of Taibah University for Science, 13(1):696-703.
[17] Bayad, H.et al. (2018). Influence of P+-ZnTe back surface contact on photovoltaic performance of ZnTe based solar cells. Optical and Quantum Electronics, 50(6):259.
[18] Sawicka-Chudy, P., Sibiński, M., Wisz, G., Rybak-Wilusz, E. and Cholewa, M., (2018),. Numerical analysis and optimization of Cu2O/TiO2, CuO/TiO2, heterojunction solar cells using SCAPS. In Journal of Physics: Conference Series ,1033( 1): 012002.
[19] Olopade, M.et al. (2017). The Study of Some Materials as Buffer Layer in Copper Antimony Sulphide (CUSbS2) Solar Cell Using SCAPS 1-D. In 2017 IEEE 44th Photovoltaic Specialist Conference (PVSC): 2381-2384
[20] Rafee Mahbub, M.et al. (2016). Simulation of CZTS thin film solar cell for different buffer layers for high efficiency performance .ENGINEERING AND TECHNOLOGY, 2(52): 1-10.
[21] Nichterwitz, M.et al. (2013). Generation-dependent charge carrier transport in Cu (In, Ga) Se2/CdS/ZnO thin-film solar cells. Journal of Applied Physics, 113(4):044515.
[22] Löckinger, J.et al. (2018). TiO2 as intermediate buffer layer in Cu (In, Ga) Se2 solar cells. Solar Energy Materials and Solar Cells, 174:397-404. [23] Simya, O. K. Mahaboobbatcha, A. and Balachander, K. (2015). A comparative study on the performance of Kesterite based thin film solar cells using SCAPS simulation program. Superlattices and Microstructures, 82: 248-261.
[24] Khattak, Y.H.et al. (2018). Numerical modeling baseline for high efficiency (Cu2FeSnS4) CFTS based thin film kesterite solar cell. 164: 547-555.
[25] Najim, A. H. & Saleh, A. N. (2019). Study effect of window and BSF layers on the properties of the CZTS/CZTSe solar cell by SCAPS–1D. Tikrit Journal of Pure Science, 24(3): 77-83.
[26] Eisele, W.et al. (2003). XPS, TEM and NRA investigations of Zn (Se, OH)/Zn (OH) 2 films on Cu
(In, Ga)(S, Se) 2 substrates for highly efficient solar cells. Solar energy materials and solar cells, 75(1-2): 17-26.
[27]Martin, A. Crane translation by Hassan, Y. M. (1989). Solar Cells Principles of Work, Technology and System Applications. Baghdad National Library. (In Arabic) [28] Khattak, Y.H.et al. (2018). Effect of CZTSe BSF and minority carrier life time on the efficiency enhancement of CZTS kesterite solar cell. Current Applied Physics, 18(6): 633-641. [29] Olopade, M. A.et al. (2012). Investigation of some materials as buffer layer in copper zinc tin sulphide (Cu2ZnSnS4) solar cells by SCAPS-1D. Advances in Applied Science Research, 3(6): 3396-3400.
[30] Zerfaoui, H.et al. (2019). The simulated effects of different light intensities on the SiC-based solar cells. Silicon, 11(4):1917-1923.
[31] Ghania, A. (2012). THEME STUDY OF SILICON SOLAR CELLS PERFORMANCES USING THE IMPURITY PHOTOVOLTAIC EFFECT. M. Sc. THESE .Université Ferhat Abbas–Setif la Faculté des Sciences Département de Physique.Algérienne.
